WICHTIGE INFORMATION

Wenn eine Anwendung mit Rev.1.4.2 oder neuer mit select_rtc oder acquire_rtc 
auf eine PCIe- oder Eth-Karte zugreifen will, auf der Rev.1.4.1 oder kleiner
läuft, funktioniert die Versionsprüfung nicht. Die Karte wird fälschlicher-
weise in Besitz genommen. load_program_file repariert den Fehler.


PCIe:

Rev. 1.2. DLL 603, OUT 603, RBF 608, DAT 601
Software aus Rev. 1.3 oder 1.3.1 läuft nicht (load_program_file() - Fehler 2)
BIOS-Version 0x11 (nicht explizit auslesbar)

Rev. 1.3: DLL 606, OUT 606, RBF 611, DAT 601
Software aus Rev. 1.2 läuft nicht (load_program_file() - Fehler 2)
BIOS-Version 0x21 oder 0x22 (auslesbar mit get_bios_version())

Rev. 1.3.1: DLL 607, OUT 607, RBF 611, DAT 601
Software aus Rev. 1.2 läuft nicht (load_program_file() - Fehler 2)
BIOS-Version 0x21 oder 0x22
Software aus Rev. 1.3 läuft möglicherweise nicht 
(load_program_file() - Timeout 30 s - Fehler 2). In diesem Fall ist ein 
Neustart der Karte erforderlich. Dann nur die Rev. 1.3 Software laden, 
nicht zuvor Rev. 1.3.1 (auch nicht mit der aktuellen laserDESK-Version 1.4.1.2,
welche Rev. 1.3.1-Files lädt).

Rev. 1.4.1: DLL 609, OUT 609, RBF 614, DAT 601
BIOS-Version 0x23
Ein Software-Wechsel zur Laufzeit (load_program_file()) mit Versionen 
Rev. 1.4.1 oder neuer ist mit Bios-Version 0x23 möglich.
Mit früheren BIOS-Versionen und/oder früheren Software-Version als Rev. 1.4.1
kann es zu Problemen kommen (incl. PC-Freeze, BlueScreen). Hier ist vor 
load_program_file ein Power-Cycle der Karte dringend empfehlenswert.

Rev. 1.4.2: DLL 610, OUT 610, RBF 615, DAT 602
WICHTIG: Es gibt eine neue DAT-File-Version 602. Ältere DAT-File-Versionen
können nicht mehr verwendet werden. load_program_file liefert sonst einen
Version-Mismatch-Fehler.

Rev. 1.4.3 war kein offizielles Release

Rev. 1.4.4: DLL 611, OUT 611, RBF 615, DAT 603
WICHTIG: Es gibt eine neue DAT-File-Version 603. Ältere DAT-File-Versionen
können nicht mehr verwendet werden. load_program_file liefert sonst einen
Version-Mismatch-Fehler.


Eth:

Hier unterscheiden sich die Bios-Versionen:
BIOS-Version 0x21: load_program_file() liefert fälschlicherweise Fehler 2, 
sofern kein anderer Fehler oder ein echter Fehler 2 vorliegt.
Prüfen z.B. mit get_overrun() und get_last_error() und ggf. 
eth_get_last_error(). Wenn beides ohne Fehler, dann läuft die Software trotz
vorheriger Fehlermeldung.
Bisher wird BIOS 0x21 mit Software Rev. 1.3 ausgeliefert.

BIOS-Version 0x22: load_program_file() läuft ohne fälschliche Fehlermeldung 2 
durch, sofern kein anderer Fehler vorliegt.
Bisher wird BIOS 0x22 mit Software Rev. 1.3.1 ausgeliefert.

Ein BIOS-Upgrade (um z.B. den load_program_file()-Fehler zu beheben) ist mit 
dem Software-Paket Rev. 1.3.1 noch nicht vor Ort möglich, jedoch mit 
Rev. 1.3.2. Man führe RTC6config.exe aus.

Rev. 1.4.1: DLL 609, OUT 609, RBF 614, DAT 601
BIOS-Version 0x23
Mit früheren BIOS-Versionen und/oder früheren Software-Version als Rev. 1.4.1
kann es zu Problemen beim Booten oder bei load_program_file kommen (Karte läuft 
nicht). Man führe daher RTC6config.exe aus, um auf BIOS 23 upzugraden. 
Mit BIOS 23 ist ein automatisches Booten aus dem integrierten Speicher
unterbunden. Damit ist nach jedem Neustart ein load_program_file zwingend
erforderlich. Ein Power-Cycle der Eth-Karte hat damit dieselbe Wirkung wie bei 
einer PCIe-Karte. Ein Software-Wechsel zur Laufzeit (load_program_file()) ist 
mit Versionen Rev. 1.4.1 oder neuer und mit Bios-Version 0x23 möglich.
Das automatische Booten wird mit einer späteren Version wieder etabliert.

Rev. 1.4.2: DLL 610, OUT 610, RBF 615, DAT 602
WICHTIG: Es gibt eine neue DAT-File-Version 602. Ältere DAT-File-Versionen
können nicht mehr verwendet werden. load_program_file liefert sonst einen
Version-Mismatch-Fehler.

Rev. 1.4.3 war kein offizielles Release

Rev. 1.4.4: DLL 610, OUT 610, RBF 615, DAT 603
WICHTIG: Es gibt eine neue DAT-File-Version 603. Ältere DAT-File-Versionen
können nicht mehr verwendet werden. load_program_file liefert sonst einen
Version-Mismatch-Fehler.
BIOS-Version 0x24
AutoIP: Wenn FORCE_DHCP gesetzt ist und innerhalb von 60 s keine IP-Adresse
zugewiesen wurde, verwendet die Karte automatisch eine link-local Adresse
(169.254.1.0/16).



IMPORTANT INFORMATION

If an application with Rev.1.4.2 or newer wants to access a PCIe or Eth card
with Rev.1.4.1 or lower by select_rtc or acquire_rtc, the version check does 
not work. The card is erroneously accessed. 
load_program_file repairs the error.


PCIe:

Rev. 1.2. DLL 603, OUT 603, RBF 608, DAT 601
Software out of Rev. 1.3 or 1.3.1 does not run (load_program_file() error 2)
BIOS version 0x11 (cannot be readout explicitly).

Rev. 1.3: DLL 606, OUT 606, RBF 611, DAT 601
Software out of Rev. 1.2 does not run (load_program_file() error 2)
BIOS version 0x21 or 0x22 (can be readout with get_bios_version())

Rev. 1.3.1: DLL 607, OUT 607, RBF 611, DAT 601
Software out of Rev. 1.2 does not run (load_program_file() error 2).
BIOS version 0x21 oder 0x22.
Software out of Rev. 1.3 does possibly not run. 
(load_program_file() - Timeout 30 s - error 2). In this case a power cycle
of the board is necessary. Then only load Rev. 1.3 software, not prior to this 
Rev. 1.3.1 (not either with the current laserDESK version 1.4.1.2, 
which loads Rev. 1.3.1 files).

Rev. 1.4.1: DLL 609, OUT 609, RBF 614, DAT 601
BIOS version 0x23
Changing the software version at run time (load_program_file()) with versions 
Rev. 1.4.1 or newer is possible with BIOS version 0x23.
With earlier BIOS versions and/or earlier software versions as Rev. 1.4.1
problems may occur (incl. PC-Freeze, BlueScreen). In these cases a power cycle 
of the board before calling load_program_file is strongly recommended.

Rev. 1.4.2: DLL 610, OUT 610, RBF 615, DAT 602
IMPORTANT: There is a new DAT-file version 602. Older DAT-file versions can't 
be used anymore. load_program_file would then return a version-mismatch error.

Rev. 1.4.3 was not an official release.

Rev. 1.4.4: DLL 610, OUT 610, RBF 615, DAT 603
IMPORTANT: There is a new DAT-file version 603. Older DAT-file versions can't 
be used anymore. load_program_file would then return a version-mismatch error.


Eth:

Here the BIOS versions differ:
BIOS version 0x21: load_program_file() erroneously returns error 2, 
provided that no other error or a real error 2 did occure.
Verify it, for example, with get_overrun() and get_last_error() and if 
applicable eth_get_last_error(). If both do not show an error, then the 
software runs despite the previous error message.
Up to now BIOS 0x21 is delivered with software Rev. 1.3.

BIOS version 0x22: load_program_file() runs without erroneous error 2,  
provided that no other error is present.
Up to now BIOS 0x22 is delivered with software Rev. 1.3.1.

Upgrading the BIOS version (for example, in order to remove the 
load_program_file() error) is not yet possible on site with the software 
Rev. 1.3.1, but with Rev. 1.3.2. Call RTC6config.exe.

Rev. 1.4.1: DLL 609, OUT 609, RBF 614, DAT 601
BIOS version 0x23
With earlier BIOS versions and/or earlier software versions than Rev. 1.4.1
problems might occur when calling load_program_file (board not running).
Execute RTC6config.exe to upgrade to BIOS version 23. With this BIOS version
an automatic boot of the program file out of the integrated memory is 
suppressed. Thus calling load_program_file is mandatory after every power 
cycle. A power cycle of the Eth board has now the same effect as power 
cycling a PCIe board. Changing the software at runtime (load_program_file())
is possible with version as of Rev. 1.4.1 and BIOS version 23.
The automatic boot of the program file will be re-established in a future 
version of the BIOS.

Rev. 1.4.2: DLL 610, OUT 610, RBF 615, DAT 602
IMPORTANT: There is a new DAT-file version 602. Older DAT-file versions can't 
be used anymore. load_program_file would then return a version-mismatch error.

Rev. 1.4.3 was not an official release.

Rev. 1.4.4: DLL 610, OUT 610, RBF 615, DAT 603
IMPORTANT: There is a new DAT-file version 603. Older DAT-file versions can't 
be used anymore. load_program_file would then return a version-mismatch error.
BIOS version 0x24
AutoIP: If FORCE_DHCP is set and no IP address is assigned within 60 seconds 
after Power-On, a link-local address (169.254.1.0/16) is automatically used.



